We are pleased to offer the following hydraulic press, subject to prior sale:
Rare offering in a used screw press... 2500 Ton Ficep Screw Press with 400mm diameter Screw capacity. This one is outfitted with hydraulic upper and lower ejectors and has optional die heater unit. FICEP SPA designs, manufactures and sells worldwide CNC controlled machines & systems for the steel construction and forging industries. | |||||||||||||||||||
|
Fill out the below for for more information on this press.. | Used FICEP Medium ton screw press with narrow distance between the side frames. These tie rods assembled machines are very sturdy and fast presses, suitable for the forging and coining of mechanical parts of medium-small size, ferrous and non ferrous material. Call for pricing, further spec details, photos and accessories included in these 2 used presses. See Maestri chain type Oven below. Call or Please e-mail Ted Gillespie
for complete details and pricing on the above listings or a complete fax list of available
type production plant presses.... 586-779-2267 |
Maestri automatic gas chain-type oven to hot air heat system to heat aluminumparts, model# : "TURBO-GAS CTA 8,700 x 700" with plates-chain, pitch 40mm, width 600mm... some general specs below.... Cod.Mecc: B8082880 Sound-proof cabin of injection fans to burners and for the cooling of fan supports.Heat chamber: Built entirely of heat-resistant stainless steel, properly ribbed and assembled with TIG welding and inox bolts. Inside dimensions of chamber: Length mm.8,700 Width mm. 700 Height mm. 240. Chainsupport sole: interchangeable elements of heat-resistant inox steel. Heat isolation: Safety device: Thickwall, first layer of fiberceramic, further layers of mit;leralwools. Heat system to recycle of hot air, set forcedly in cycle by means of four (4) Turbines suitable to work with hot air up to 600°C. The air is uniformly distributed into the chamber vault and it is blown upon the heating parts from a series of nozzles that lead the air right on the parts. A fan sucks up the air to the bottom of the chamber, underneath the chain, and send it into the burner chambers, where the air temperature integrates by mixing with the combustion gases of burners. The hot air is then sent to the upper chamber and blown again into the chamber. On the oven are foreseen eight (8) industrial burners. On average the air makes 25/30 cycles per minute.
Temperature regulation: Automatic, proportional type, divided over 8 independent heat control areas, by 8 digital precision Thermoregulators and 8 double joint. Thermocouples type K. Temperature adjustable +200° (395°F) to +550°C (1030°F).Tolerance 0.5/'0 end scale. OFF05.108.inalese with US $.doc. Requested Productions mostly Aluminum rough parts: and Sizing of oven : 02.5" (=63.5mm) x length 11" (=280mm) ; weight 2.4 Kgs and production adjustable 1to 10 ppm (according to output of oven). Rough parts transport chain : Plates-type chain with V-seats to lacate the parts, pitch 40mm. Chaintotal width: 600mm. Bar and disc rough parts can be loaded automatic upon the chain of oven, whereas preformed parts can be hand loaded by using a specific load-in area at entrance of oven. Feeding of the chain made by pitch, by geared motor and self-braking motor controlle by management and control system of oven. The chain is made by Maestri entirely of stainless steel and do not requires any particular servicing. Billet automatic loader is a 500mm 'BRC'automatic loader, suitable to feed in automatic parts with the following cdimensions: Bar bilIets with (2}: Length : 35mm to 80mm (2}+40mmto 380/400mm or Disc billets with: Thickness: Max. weight of billets allowed in automatic: (2}80mm to 160mm The billets coming out of the feeding system (BRC)are carried upona transversal chain, where a selecting system selects the number of billets to be loaded to each cycle. The introduction of the billets uponthe transport chain is made through a pneumatic system, synchronized to the chain inside length. The whole introduction system is controlled by PLC of oven management.
Billets unloading: Unloading of rough parts made by gravity through inclined slide in the final part of oven. A chain for the transport of the hot parts will be located at end of the slide, right near the operator to the press. Orientation and length of the chain will be fixed according to final lay out of the plant. THE OVEN IS EQUIPPED WITH: Control panel to CEl rules, floor standing type with connectors to the oven. Standard instrumentation installed on the oven is the following: PLC SIEMENS S7 300 with Operative panel SIEMENS S77. The software controls and checks that the requested production is attainable with the oven, informing the operator if the performance required overcomes the productive capacity of oven. The signal can be managed as bright signal or arranged to stop the work cycle, according to the customer needs. In the standard system, PLC is SIEMENS S7 300 and operative panel is SIEMENS OP77. Besides the a.m. characteristic, with this system it is also possible to verify on the panel the operating data as: production pph, Kgph, heat time of the working parts, real heat time, diagnostic of special functions of the system, information about programmed maintenance.
23 Hydraulic Compression Molding Presses from 500 ton to 2500 ton for sale at liquidation prices. (Shelbyville Indiana auto parts plant)
Grabill Indiana Compression Molding plant liquidation sale on 14 ERIE, French Oil, Hepburne and Williams & White compression molding presses ranging from 400 to 4450 ton capacities. Also HPM Injection Molding presses for immediate sale on same page.
HPM 1500 ton Deep Draw Hydraulic Press for sale by Paramount Industries Inc.
We are pleased to offer for your consideration the following used
hydraulic HPM stamping press. (1) HPM 1500 ton Deep Draw Hydraulic Press Serial: 4084 and total Capacity - 1500 ton Die cushion - 600 ton Bolster size - 60" x 60" Stroke - 30" - Open height - 50" Bolster thickness - 10" Advance speed - 400 IPM Pressing speed (up to 500 tons) - 58 IPM Pressing speed (500-1500 tons - 17.5 IPM Return speed - 400 IPM Motor - 100 HP - 175 amp at 480 volt Approximate weight - 185,000 lbs. Approximate overall dimensions - 8' x 9' x 23' Features: HPM radial pump and full controls Stock Number: - 11076 - |
Click to Enlarge |
* #100 Ton Minster PM3 * #1000 Ton Danly Press . Model# SE4-1000 * #1000 Ton Danly SE4-1000-108-84 * #1000 Ton U.S.I Clearing 4-Point Straight Side Presses * #300 TON MINSTER HEAVY STAMPER *#600 TON MINSTER HEAVY STAMPER SSDC PRESS * #800 TON DANLY S4-800 * #800 TON WARCO PRESS * #SE2-600-120 x 60 CMC-BLISS PRESS * #USI -CLEARING 600 Ton *
1500 ton Klockner Plastic Injection Molding
Press (like new)
USI CLEARING 6-PRESS
MECHANICAL PRESS LINE
1 x 1300-TON DOUBLE ACTION Press Plus 5 X 450-TON SINGLE ACTION Presses are part
of this sale
3500 Ton HPM 4 POST Hydraulic Press
-distressed sale price
5000 Ton Lake ERIE Triple Action Hydraulic
Press
5000 Ton BLISS 4 POST Hydraulic
Press at a liquidation price
1500 Ton SAVAGE
Traveling Gantry Straightening Press
1500 Ton HPM Deep Draw 4 post hydraulic press for sale
8000 Ton AP&T Hydroforming frame
Press -like new
Unique opportunity to own 5 complete working automotive industry
presslines
586-779-2267 sales@EquipBrokers.com
Buyers Agent helpline: 1-800-882-6165
Offer To Purchase Agreement | Listing & Brokerage Agreement | Information Request Form | Want To Purchase